Exmark LZS749AKC604A1 » H&R Agri-Power, Kentucky, Illinois, Tennessee, Alabama, Mississippi and Indiana (2024)

Features

Doing More With Propane

Our EFI system optimizes fuel delivery in real-time, which improves efficiency and performance. This, in combination with lower propane cost reduces operating expenses versus typical gas-powered mowers.

Less Time At The Pump

Gas-powered S-Series models have a single 12-gallon tank with one fill location.

Built to Last

Want tough? Try a 10-gauge, formed and continuously seam-welded top, and a 7-gauge side skirt. All with welded spindle mounting sites. And, full-floating, 4-point suspension with four adjustable anti-scalp rollers.

On-Board Diagnostics

Check vital functions at a glance on the digital screen. An electronic fuel gauge with low fuel warning on all Lazer Z units, battery voltage warning, hour meter and OPC safety switch monitoring make troubleshooting easy.

Fewer Grease Points

With just four grease points that only need annual greasing, the Lazer Z delivers maximum performance with minimum maintenance. Grease-less spindles and only four grease points on the entire machine.

Ultracut Series 4 Deck

This full-floating deck uses maintenance free spindle with a splined blade driver to stop bolt tightening on impacts. And, our patented bearing design on idler arm pivots only needs annual service.

Tool-less Belt Removal

Deck and hydro belt can be installed without using any tools.

Specs

Equipment
Blade SpindlesNo maintenance, sealed and non-greasable spindles; 7.75"-diameter cutter housing with 25mm (1.18")diameter spindle shaft and splined blade driver.
Drive Tires24 x 12-12, 4 ply Turf Master®
Cup HolderStandard
Tractor FrameUnibody, welded, heavy-duty 1.5" x 3" tubular steel.
Steering ControlHydraulically dampened twin levers, adjust fore and aft. Adjustable dampeners (3 positions) to customize drive responsiveness. Also adjustable to 2 height positions.
Front Caster Tires13 x 6.5-6, smooth-tread, semi-pneumatic.
Parking BrakeLever-actuated disc brake.
SeatDeluxe, two-tone, bolstered suspension seat with Elastomeric Vibration Control material. Mounted on innovative Seat Isolation System that provides operator isolation in all three planes of motion as well as fore-aft slide and seat flip-up.
Electrical12-volt battery with 20-amp alternator.
Onboard IntelligenceSmart Controller
Standard FeaturesEngine hour meter and cup holder
UPC193308000572
Power Components
Engine BrandKohler®
Engine ModelECV749
Engine Displacement747
Engine SeriesCommand™ EFI
Engine TypeElectronic Fuel Injected
Engine Speed3,750 rpm
Air FilterHeavy-duty canister air filtration system
Fuel TypeGas EFI
Fuel Capacity12-gallon (45.4-L), single fuel tank with single fill location.
Fuel IndicatorYes - electronic Sender
DriveHydro-Drive
Drive DescriptionTwo Exmark exclusive Parker unitized pump and wheel motor systems with no hoses, integrated cooling fans, 1.7-quart integrated reservoir, spin-on filter and heavy-duty components. 12 cc pumps and 14. 5 cubic inch motors.
SpeedInfinitely variable speed selection from 0-10.0 mph (16 kmph) forward, 0-6.0 mph (9.7 kmph) reverse.
Carb CompliantYes
Deck LiftStandard; foot-controlled deck lift changes cutting height and lifts the deck to maneuver around obstacles, or place in transport position.
Safety PackageOperator Presence Controls (OPC) and drive system interlock, with safety interlock system indicators.
ROPS2-post foldable ROPS standard with seat belt and latch.
PTO EngagementMagStop electromagnetic 200-ft-lb clutch with spot brake
Drive Wheel ReleaseAllows unit movement without engine running.
Casters.50" thick caster yoke arms.
Engine Spec3064
Decks
Width / Cutting Deck60"
Deck StyleFloating Deck
Deck Style DescriptionFull-floating UltraCut Series 4. Side discharge standard, with molded discharge chute and option to bag or mulch.
Deck Construction10-gauge top that is formed and continuously seam welded, 7-gauge side skirt and 7-gauge formed and welded spindle mounting locations for improved strength and reduced weight.
Blade Tip SpeedApproximately 18,500 fpm.
Cutting Heights1.0" (2.5 cm) to 5.5" (11.8 cm) in 0.25" (0.64 cm) increments adjustable from operator's seat.
Blades3 Blades at 20.50" Length
Dimensions
Width72.8 in. (184.9 cm)
Length83.1 in. (211.1 cm)
Height70 in. (177.8 cm)
Curb Weight1177

Accessories and Attachments

Equipment Cover

Protect your zero-turn mower from the elements with this sturdy, waterproof cover. It’s constructed from tough 600-denier polyester, making it abrasion- and tear- resistant. Its elastic opening provides a secure, snug fit.

Power Deck Lift

Change your deck from any cutting height to the transport position quickly and easily, with a convenient foot pedal actuator switch that lets you keep your hands safely on the drive levers. Created specifically for your 48-72" cutting deck Lazer Z, its electronic motor features Exmark's signature durability and a low-profile design that leaves plenty of trailer space.

Trash Container (Not compatible with 135-7320)

Conveniently located within easy reach of the operator, this trash container features a 2.5-gallon capacity and durable, easy-to-clean mesh receptacle. See dealer for fit- up information.

Anti-Scalp Roller Kit

Protect the trim side of your Lazer 60" UltraCut deck with this Anti-Scalp Roller kit. Fits Lazer 604 decks model year 2009 and above.

UltraVac 3-Bag Collection System

The UltraVac S-Series enables you to switch between bagging and side discharge with quick-attach capability. Avoid clogging with larger diameter tubes. Compact design minimizes trailer space for easy maneuverability. Sealed hood reduces dust.

Floor Mat

Keep your Lazer looking its best by protecting the floorpan from scuffs and dirt. Fits all Lazer models (model year 2009 and higher).

Air Ride Suspension Seat

Designed to fit all Lazer Z models, the new air ride seat gives you the best comfort available. Sophisticated air suspension technology virtually eliminates any bumps, jarring or vibration your property delivers.

12-Volt Power Port

Extended Drive Lever Kit

Improve your elbow room while you operate with extended drive levers.

UltraVac Completing Kit

KIT, UV DRIVE 604 SPLINED 850,000 +

Light Kit (not compatible with TC26)

Keep mowing after the sun goes down with brilliant, 27-watt halogen power from this Hella® Work Lamp Kit. Easily mounted to your ROPS bar, the highly durable lenses repel dust, withstand impact, and can even take on high- pressure cleaning. With twice the illumination output of a conventional work lamp, the kit also features a pivot base and easy bulb replacement.

Sun Shade (ROPS)

Easily mounts to Rollover Protection System (ROPS). Made of heavy-duty, water- repellent canvas for maximum durability. Easily removable for transport. Fits all Lazer Z and Pioneer models. (Does not fit Quest.) (Replaces 116-0513)

Wiring Harness Relay

Micro-Mulch System

The aerodynamically designed deck, baffles and blades create airflow patterns that circulate leaves and grass for repeated cuttings and even dispersal deep into the turf. Mulching baffles also keep the underside clean, which reduces grass buildup and clumping.

UltraVac Quick Dump Collection System

The UltraVac X-Series discharges grass quickly with one simple motion of the release lever. With commercial-grade steel and polyethylene hopper Get the job done efficiently with rear-discharge door, and 11 bushel capacity.

Hydro Maintenance Kit

Kit includes: 1 gallon jug of Exmark® Premium Hydraulic Oil and 2 Hydro Filters (Replaces 116-3270)

Harness Add-On Accessory Kit

Take the hassle out of dual accessory fit up with this add-on harness.

Turf Striping Kit

Fits 48", 52" and 60" models. Customize your property with consistent and professional striping using a smooth operating roller design. Installs quickly, using existing mounting points, and easily adjusts for varying cutting height settings. Does not affect your ability to get up and over curbs.

3-Bushel Bagger

Lightweight and easy to attach, this 3-bushel grass catcher fits all Exmark Lazer Z, Pioneer, Radius, Vantage* and wide-area walk-behinds. (*Not available for Vantage Propane models.)

Jack Mount Receiver

Safely access the underside of your zero-turn mower’s deck. Used with Exmark's Bulldog jack (p/n 127-6666 sold separately) attaches for smooth lift without hassle or strain, thanks to its comfortable, ergonomic design. Built for years of reliability.

Operator Controlled Discharge (Foot) (C1 needs 135-0100)

The infinitely adjustable blocker door opens and closes by using the convenient foot pedal, allowing the operator to quickly control discharge when mowing around parked cars and windows. Easily installs and removes without tools. (C1 needs 135-0100)

Jack

Easy to use, 15" stroke Bulldog jack, gives you plenty of room to change blades or perform routine deck cleaning (jack mount receiver not included).

Hitch Kit

Enables owners to add attachments to their mowers to increase productivity by towing light implements and yard carts.

Tractus Tire

Designed to eliminate the flat tires that increase downtime. Exmark designed the Tractus tire and wheel combination to offer a similar ride quality to a pneumatic tire.

Exmark LZS749AKC604A1 » H&R Agri-Power, Kentucky, Illinois, Tennessee, Alabama, Mississippi and Indiana (2024)

References

Top Articles
Latest Posts
Recommended Articles
Article information

Author: Kelle Weber

Last Updated:

Views: 5331

Rating: 4.2 / 5 (53 voted)

Reviews: 84% of readers found this page helpful

Author information

Name: Kelle Weber

Birthday: 2000-08-05

Address: 6796 Juan Square, Markfort, MN 58988

Phone: +8215934114615

Job: Hospitality Director

Hobby: tabletop games, Foreign language learning, Leather crafting, Horseback riding, Swimming, Knapping, Handball

Introduction: My name is Kelle Weber, I am a magnificent, enchanting, fair, joyous, light, determined, joyous person who loves writing and wants to share my knowledge and understanding with you.